FS OP/MOLD HANDLER
Estimated Pay | $12 per hour |
---|---|
Hours | Full-time, Part-time |
Location | Wichita Falls, Texas |
Compare Pay
Estimated Pay$9.44
$12.30
$17.56
About this job
Howmet Aerospace's Wichita Falls, TX facility has openings for Foundry Service Operator/Mold Handlers.
Howmet is a world leader in the investment casting industry and is a leading supplier of superalloys, aluminum, and titanium components for aerospace, automotive, and commercial transportation applications. Our Wichita Falls location is on the front edge of the rapid growth in the aerospace and turbine industries. For more information, visit . Follow @howmet: Twitter, Instagram, Facebook, LinkedIn and YouTube.
Must be able to work rotating shifts. This Opening will be on a 7:00 p.m. to 7:00 a.m. shift . Training may take place on days.
(Rotating shifts work 2 on 2 off, 3 on 2 off, 2 on 3 off)
JOB SUMMARYWorks under general supervision and the direction of a caster to remove molds from the preheat furnace, properly position in timely manner for casting, perform wrap application, dewax, repair and mold inspect, and perform all post-cast operations specified.
ESSENTIAL FUNCTIONS
- Using Computers (entering information, etc.)
- Must be able to read and interpret Product Criteria (PC) and Activity Instructions (AI).
- Must be able to function as a member of a team and be able to work under general supervision.
- Must be able to maintain expected quality levels.
- Comply with all site required policies and procedures including but not limited to: EHS, Quality, Code of Conduct and the Wichita Falls Employee Handbook.
- Read all available instructions and assist caster to cast molds in accordance with established techniques and specific instructions on the Product Criteria, Mold Sheets, or Activity Instructions.
- Requires concentration for short periods of time when assisting in the acquisition of the proper alloy, checks preheat temperatures, handles the molds from the preheat furnace and again after casting, and accomplishes all specific post-cast operations (Mold hot topping, exothermic application and vermiculite encapsulation).
- Particularly responsible for proper mold positioning, lower chamber cleaning, and the control of variables affecting solidification and mold cooling.
- Moves empty, hot furnace trays, changes and cleans floor gaskets, performs heavy housekeeping required in department, and assists in minor equipment maintenance.
- Notifies caster of any torn wraps, bumped or leaking molds.
- Periodically required to load ovens.
- Keep updated on new methods on improvements.
- Must follow all safety practices and procedures.
- Rotates through each job duty as required.
- Locates scheduled work, moves trucks to proper work station.
- Ensures molds are kept clean in each area.
- Seals molds at dewax or mold inspection with either ceramic disk or rubber cap.
- Monitors operation of equipment and temperature controls.
- Must follow work instructions, SOP's, and activity instructions that govern each job task.
- Inspects and repairs molds.
- Prepares solutions and maintains supplies.
- Cuts required kaowool and roll board.
- Wraps molds per process releases/product criteria.
- Must be able to operate the required piece of mobile equipment for this area.
- Machines and work area are to be kept clean and in orderly condition. Supervisor is to be notified immediately of equipment or machinery malfunctions.
- Completes necessary paperwork as required.
- Verifies mold counts and paperwork correctness on lot travelers, or serial numbers at each operation.
- Loads molds in preheat oven.
- Performs other duties as required.
- Complies with all EHS rules related to the work environment.
- Works overtime when needed
Physical Demands:
The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilites to perform essential functions.
Employee is required to execute the following:
Work Environment: (Chemical and Physical Exposures)
- Extreme care must be taken because of exposure to extremely high temperatures for short periods of time.
- Exposure to dust and fumes from the casting process.
- Occasional exposure to uncontained molten metal sprays and solid metal chips from chamber cleaning.
- Exposure to Nickel and RCF.
- Requires wearing dust mask/respirator during certain procedures.
Basic Qualifications:
- High School Diploma or GED from an accredited institution.
- Employees must be legally authorized to work in the United States. Verification of employment eligibility will be required at the time of hire. Visa sponsorship is not available for this position.
- To ensure the health and safety of our employees, Howmet requires newly hired employees to be fully vaccinated for COVID-19 to the extent permitted under federal, state, and local law. Requests for reasonable accommodations on the basis of a disability, medical condition, or sincerely held religious beliefs or legally recognized exemptions will be considered.
PREFERRED QUALIFICATIONS:
- Basic Computer skills.
- Foundry Service Operator/Mold Handler experience
- Job Identification 108552
- Job Category Operations
- Posting Date 04/02/2024, 02:20 PM
- Locations PO Box 1616, 6200 Central Frwy, Wichita Falls, TX, 76307-1616, US
- Job Schedule Full time
- Remote Work Schedule Availability? None
- ITAR This position entails access to export-controlled items and employment offers are conditioned upon an applicant's ability to lawfully obtain access to such items